40 Caliber Volcanic Rifle,

Welcome to the Leverguns.Com Forum. This is a high-class place so act respectable. We discuss most anything here ... politely.

Moderators: AmBraCol, Hobie

Forum rules
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.

Please post political post in the new Politics forum.
Charlie
Levergunner 2.0
Posts: 149
Joined: Thu Nov 19, 2009 11:56 am

40 Caliber Volcanic Rifle,

Post by Charlie »

What a Sweet Little Rifle!

Trim, Slender, Beautifully proportioned, Sexy Little Action, fun to look at, and fun to play with.

Not only that, this is where it all began, "Lever Guns" that is.

Image

Below is a 21" Barrel Carbine.

Image

The original Volcanic shot a short little Bullet called the "Rocket Ball", it was less than .650 Lg. and had very little power, but this Rifle had the genes to become the legendary Winchester.
It goes like this;

The Volcanic was enlarged to become the "Henry",
The "Henry" was improved to become the "Winchester 66"
The 66 was improved to become the "Winchester 73"
The 73 was enlarged to become the 76.
And then Mr. Browning came along with a much stronger, smaller action, and replaced the "Toggle Link System", invented by Mr. Smith and Mr. Wesson, which was used in the Volcanics through the 76.

Above is my design, based on the Toggle Link System. My design is stronger than theirs, and easier for me to build.
While designing this gun, I tried to copy the original dimensions and proportions. I do not have access to an original, so I have had to "scale" photographs to come up with what I have.
The first problem I came to was this Little Action would not shuffle and shuck any available cartridges except the "22 Short"! This did not excite me so I designed my own "Wildcat 40". I will describe it to you later.

This is not a "Kit", or a modification of another "Lever Gun" I will not be using purchased parts, or parts from other Guns. I will use a purchased Barrel Blank from "Douglas" (40 Caliber, 1 in 14 twist) cut it, mill it, thread it, and chamber it for this Rifle. Everything else, including the Springs and most of the Screws, I will make from scratch.

I do this for fun, nothing else, I do not build guns for other people, or plan to go in to the business someday.

I am here to share Guns and Friendship with you Guys.

I hope you will enjoy this build.

Later,

Charlie
Last edited by Charlie on Sat Mar 27, 2010 9:43 am, edited 7 times in total.
User avatar
gamekeeper
Spambot Zapper
Posts: 17323
Joined: Thu Sep 06, 2007 3:32 pm
Location: Over the pond unfortunately.

Re: 40 Caliber Volcanic Rifle,

Post by gamekeeper »

Fantastic! Thanks for sharing your incredible hobby with us all. 8)
If more men loved and cherished their wives as much as I love bacon the world would be a much better place.
Ben_Rumson
Advanced Levergunner
Posts: 2569
Joined: Sat Sep 15, 2007 12:51 pm

Re: 40 Caliber Volcanic Rifle,

Post by Ben_Rumson »

This is a neat project.. I'm pretty sure I've read about this somewhere else on the net.. The 40 cal ammo rings a bell..
"IT IS MY OPINION, AND I AM CORRECT SO DON'T ARGUE, THE 99 SAVAGE IS THE FINEST RIFLE EVER MADE IN AMERICA."
WIL TERRY
User avatar
Buck Elliott
Member Emeritus
Posts: 2830
Joined: Mon Sep 10, 2007 12:15 pm
Location: Halfway up Sheep Mountain -- Cody, Wyoming

Re: 40 Caliber Volcanic Rifle,

Post by Buck Elliott »

Ben_Rumson wrote:This is a neat project.. I'm pretty sure I've read about this somewhere else on the net.. The 40 cal ammo rings a bell..
Same here ...

Keep us posted, Charlie.
Regards

Buck

Life has a way of making the foreseeable that which never happens, and the unforeseeable, that which your life becomes...
User avatar
Ysabel Kid
Moderator
Posts: 27790
Joined: Mon Sep 17, 2007 7:10 pm
Location: South Carolina, USA
Contact:

Re: 40 Caliber Volcanic Rifle,

Post by Ysabel Kid »

Please, please, PLEASE take lots of photos along the way. This is going to be a fascinating project to watch!!! 8)
Image
User avatar
Buck Elliott
Member Emeritus
Posts: 2830
Joined: Mon Sep 10, 2007 12:15 pm
Location: Halfway up Sheep Mountain -- Cody, Wyoming

Re: 40 Caliber Volcanic Rifle,

Post by Buck Elliott »

Ysabel Kid wrote:Please, please, PLEASE take lots of photos along the way. This is going to be a fascinating project to watch!!! 8)
Just make sure you include your feet in a couple of 'em... :lol:
Regards

Buck

Life has a way of making the foreseeable that which never happens, and the unforeseeable, that which your life becomes...
User avatar
JReed
Advanced Levergunner
Posts: 5509
Joined: Tue Apr 03, 2007 11:17 am
Location: SoCal

Re: 40 Caliber Volcanic Rifle,

Post by JReed »

Yes don't leave us out on the details. I am most interested in seeing how this project comes together for you.
Jeremy
GySgt USMC Ret

To err is human, To forgive is devine, Neither of which is Marine Corps policy
Semper Fidelis
Kansas Ed
Senior Levergunner
Posts: 1261
Joined: Tue Sep 18, 2007 8:08 pm
Location: Wichita

Re: 40 Caliber Volcanic Rifle,

Post by Kansas Ed »

I for one, might be interested in the .22 short version. I think one in the short would be a fantastic squirrel rifle. And we sure do have limited selection of a clean line high quality .22 short lever gun IMO.

Ed
Cliff
Levergunner 3.0
Posts: 593
Joined: Fri Sep 07, 2007 6:55 am

Re: 40 Caliber Volcanic Rifle,

Post by Cliff »

I suppose if you wanted to stick with a rimfire, you could build it in a 41 remington rim fire used in the old derringers. Still plenty low powered. I will be quiet now. Good Luck.
Bis
Levergunner 2.0
Posts: 291
Joined: Sat Feb 23, 2008 6:25 pm
Location: Crockett, Texas

Re: 40 Caliber Volcanic Rifle,

Post by Bis »

What a great project. Please post pics
when your enemy is within range so are you
User avatar
kimwcook
Advanced Levergunner
Posts: 7978
Joined: Tue Sep 04, 2007 10:01 pm
Location: Soap Lake, WA., U.S.A.

Re: 40 Caliber Volcanic Rifle,

Post by kimwcook »

Cool. Can't wait to see the final project. Hope you don't pull too much hair out along the way or you're like me and don't have any left to pull. :D
Old Law Dawg
Chuck 100 yd
Advanced Levergunner
Posts: 6972
Joined: Tue Apr 03, 2007 8:52 pm
Location: Ridgefield WA. USA

Re: 40 Caliber Volcanic Rifle,

Post by Chuck 100 yd »

:mrgreen: Cant wait....... Can you post drawings of the parts or sell drawings for those wanting to try their hand at fabing one up? There are several here that are handy enough to do it. :mrgreen:
dsmith512
Levergunner 2.0
Posts: 103
Joined: Thu Sep 13, 2007 8:09 am

Re: 40 Caliber Volcanic Rifle,

Post by dsmith512 »

Like many here, it seemed like I heard of a project like this before with a 40 caliber round. I dug through the archives and found a thread posted by Old Ironsights about a Homebuilt Volcanic

http://www.levergunscommunity.com/viewt ... w=previous

The round was a modified S&W 40.

Homemade Volcanics just seem way Cool :D
User avatar
Griff
Posting leader...
Posts: 20803
Joined: Sat Mar 31, 2007 4:56 pm
Location: OH MY GAWD they installed a STOP light!!!

Re: 40 Caliber Volcanic Rifle,

Post by Griff »

8) 8) or "2 cool"
Griff,
SASS/CMSA #93
NRA Patron
GUSA #93

There is a fine line between hobby & obsession!
AND... I'm over it!!
No I ain't ready, but let's do it anyway!
User avatar
pokey
Advanced Levergunner
Posts: 2704
Joined: Mon Feb 09, 2009 10:19 pm
Location: La center, wa.

Re: 40 Caliber Volcanic Rifle,

Post by pokey »

Griff wrote:8) 8) or "2 cool"

maybe, three cool :wink:
careful what you wish for, you might just get it.

"BECAUSE I CAN"
Charlie
Levergunner 2.0
Posts: 149
Joined: Thu Nov 19, 2009 11:56 am

Re: 40 Caliber Volcanic Rifle,

Post by Charlie »

dsmith512 wrote:Like many here, it seemed like I heard of a project like this before with a 40 caliber round. I dug through the archives and found a thread posted by Old Ironsights about a Homebuilt Volcanic

http://www.levergunscommunity.com/viewt ... w=previous

The round was a modified S&W 40.

Homemade Volcanics just seem way Cool :D
I am the builder of that Pistol.

I documented that build on another website that required money to be a member.

Over here, it's free!

Enjoy it my Friends, that is my only reward.

Let's just have some fun doing things that have not been done before.

Later,

Charlie
Ben_Rumson
Advanced Levergunner
Posts: 2569
Joined: Sat Sep 15, 2007 12:51 pm

Re: 40 Caliber Volcanic Rifle,

Post by Ben_Rumson »

Well Charlie, now that you have it figured, here's a pick that would have made things easier to scale from..Easy to see the changes you made to the toggles now that I finally saw your pistol from where you originally posted.. cool!
Image
"IT IS MY OPINION, AND I AM CORRECT SO DON'T ARGUE, THE 99 SAVAGE IS THE FINEST RIFLE EVER MADE IN AMERICA."
WIL TERRY
soon 2 retire
Levergunner 2.0
Posts: 367
Joined: Sat Oct 25, 2008 8:43 pm
Location: San Juan Island, WA

Re: 40 Caliber Volcanic Rifle,

Post by soon 2 retire »

Charlie,

I find this really interesting. I am curious about your background, machinist by trade? Self-taught? And will you please tell what kind of lathe and mill do you use?

Bob in NE Indiana
Don't look back something might be gaining on you.
-Leroy "Satchel" Paige
Charlie
Levergunner 2.0
Posts: 149
Joined: Thu Nov 19, 2009 11:56 am

Re: 40 Caliber Volcanic Rifle,

Post by Charlie »

That picture was taken by a well known Gunsmith named "John Taylor", he had this gun in his shop doing some restoration.

Yes, that would have been a great help, but I didn't have it at the time, so I did the best I could.


About the Cartridge that I'm shooting,

Image

It has been correctly noted that this gun will shuffle, shoot, and shuck the "22 Short", also the (sometimes available) 41 Derringer.

Even though these are an improvement over the original "Rocket Ball", I am not very impressed with either of them.

The actual caliber of the #2 Rocket Ball was .41. So that is why I set out to develope my own cartridge.

I figured it like this; if I can't build my own cartridge, then I'm not gonna be able to build this gun.

I do agree somewhat with the Guys that would want this gun in "22 Short", it's not for me, but it would make a nice little Squrrel Gun.

I shortened a 40 S+W case to .550, I reamed out the inside to accept the Bullet. The Cartridge shown is loaded with "Berry's 135 grain" copper plated bullet being shoved out of an 8" barrel at 1020 FPS in front of 4 grains of "Bullseye". I have fired this Cartridge out of a 25" barrel and lost nearly 100 FPS ! I don't like this load as it does show signs of pressure. I have been shooting a 140 grain cast bullet in front of 3.5 grains of "Power Pistol", here I am getting 890 FPS, and visual inspection shows only moderate pressure.

The Cartridges shown above are shown in compairson to "22 Long Rifles"

HEY I LIKE THIS PLACE.

There is a lot of enthusiasm here.

Overlook my spelling please.

Later Charlie
Last edited by Charlie on Sat Nov 21, 2009 8:56 am, edited 1 time in total.
Charlie
Levergunner 2.0
Posts: 149
Joined: Thu Nov 19, 2009 11:56 am

Re: 40 Caliber Volcanic Rifle,

Post by Charlie »

soon 2 retire wrote:Charlie,

I find this really interesting. I am curious about your background, machinist by trade? Self-taught? And will you please tell what kind of lathe and mill do you use?

Bob in NE Indiana
I am a Mechanical Engineer and Machine Designer. I was a Machinist a long time ago.

I have a "Bridgeport" and a "1955 Tool Room Hendy". I also have a small, but very robust "CNC Tabletop Mill", which I built myself.
User avatar
kimwcook
Advanced Levergunner
Posts: 7978
Joined: Tue Sep 04, 2007 10:01 pm
Location: Soap Lake, WA., U.S.A.

Re: 40 Caliber Volcanic Rifle,

Post by kimwcook »

Again, cool. Sounds like this is gonna be fun.
Old Law Dawg
User avatar
TedH
Advanced Levergunner
Posts: 8248
Joined: Tue Apr 03, 2007 5:19 pm
Location: Missouri

Re: 40 Caliber Volcanic Rifle,

Post by TedH »

Keep us updated with pics as you progress.
NRA Life Member
Charlie
Levergunner 2.0
Posts: 149
Joined: Thu Nov 19, 2009 11:56 am

Re: 40 Caliber Volcanic Rifle,

Post by Charlie »

In all my research, I have found this book to be the most informative.

That's a Beautiful 20" Volcanic on the cover.

Image
Charlie
Levergunner 2.0
Posts: 149
Joined: Thu Nov 19, 2009 11:56 am

Re: 40 Caliber Volcanic Rifle,

Post by Charlie »

OK, let's get started.

This is a basic Barrel Blank by Douglas. It is 1.300 O.D., I will put it between Centers and turn it end to end, 1.25 and then cut off each end to have a barrel 25.09 Lg. (the rifleing is not perfect at the very ends is the reason you cut off both ends.)

Image
Last edited by Charlie on Sat Nov 21, 2009 1:45 pm, edited 1 time in total.
Charlie
Levergunner 2.0
Posts: 149
Joined: Thu Nov 19, 2009 11:56 am

Re: 40 Caliber Volcanic Rifle,

Post by Charlie »

Useing a Center in the Tail Stock, I single pointed this Thread. It is 11/16 - 20 UN X .875 Lg.

Image
Charlie
Levergunner 2.0
Posts: 149
Joined: Thu Nov 19, 2009 11:56 am

Re: 40 Caliber Volcanic Rifle,

Post by Charlie »

Turning the barrel around and once again using the Tail Stock Center, I turned this Muzzle Extension. That is a 11/16 - 20 Left Hand Thread you are looking at here, the extension is .624 Dia.

Image
Charlie
Levergunner 2.0
Posts: 149
Joined: Thu Nov 19, 2009 11:56 am

Re: 40 Caliber Volcanic Rifle,

Post by Charlie »

Not much to see here, but this is to become the Magazine Block. It has a drilled and reamed hole through it and that 11/16 -20 Left Hand Thread cut in one end.

We will thread this over the Muzzle Extension, and take the assembly to the Milling Machine where they will get their Octogon shape, also a .281 Radius trench milled the intire length along the bottom.

Image
Charlie
Levergunner 2.0
Posts: 149
Joined: Thu Nov 19, 2009 11:56 am

Re: 40 Caliber Volcanic Rifle,

Post by Charlie »

I like using a double vice setup when milling long bars like this.

This Barrel wants to have a slight taper, so I put a .040 shim under the Muzzle while milling the flats.

This is a picture from a previous Barrel, but the Idea is the same.

Image
Last edited by Charlie on Tue Nov 24, 2009 7:57 am, edited 1 time in total.
Charlie
Levergunner 2.0
Posts: 149
Joined: Thu Nov 19, 2009 11:56 am

Re: 40 Caliber Volcanic Rifle,

Post by Charlie »

Hey Guys, I can't continue like this. I have been here over 4 hours today trying to post these pictures.

Photobucket won't let me resize my pictures and this sight will not accept the pictures directly from my old camera.

I had tried some other photo storage sites and could not make them work for me at all.

Maybe I can figure this out some day.

Meanwhile, I got a gun to build.


OK, I'm on a more powerful computer this morning and things are working for me.

Remember I had threaded the Magazine Block on the Barrel extension and put the intire assembly in the milling machine to mill the outside flats and magazine trench? Well here it is off the milling machine.

Image
Last edited by Charlie on Tue Nov 24, 2009 8:03 am, edited 2 times in total.
JohndeFresno
Advanced Levergunner
Posts: 4559
Joined: Fri Sep 07, 2007 1:52 pm

Re: 40 Caliber Volcanic Rifle,

Post by JohndeFresno »

Very interesting stuff, Charlie. Thank you for the effort, info, and pix!
Chuck 100 yd
Advanced Levergunner
Posts: 6972
Joined: Tue Apr 03, 2007 8:52 pm
Location: Ridgefield WA. USA

Re: 40 Caliber Volcanic Rifle,

Post by Chuck 100 yd »

Very good Charlie. Keep it coming as you can Please!! :D
User avatar
Buck Elliott
Member Emeritus
Posts: 2830
Joined: Mon Sep 10, 2007 12:15 pm
Location: Halfway up Sheep Mountain -- Cody, Wyoming

Re: 40 Caliber Volcanic Rifle,

Post by Buck Elliott »

Photobucket will allow you to resize -- at least that has been my recent experience...

Keep takin' pictures. I'm sure a way will open up to post them.
Regards

Buck

Life has a way of making the foreseeable that which never happens, and the unforeseeable, that which your life becomes...
Charlie
Levergunner 2.0
Posts: 149
Joined: Thu Nov 19, 2009 11:56 am

Re: 40 Caliber Volcanic Rifle,

Post by Charlie »

Buck Elliott wrote:Photobucket will allow you to resize -- at least that has been my recent experience...

Keep takin' pictures. I'm sure a way will open up to post them.
I know Buck, that's the way I got the pictures above to show up. After 6 to 8 trys it would finally let them down size. Now it simply don't work for me anymore.
Kansas Ed
Senior Levergunner
Posts: 1261
Joined: Tue Sep 18, 2007 8:08 pm
Location: Wichita

Re: 40 Caliber Volcanic Rifle,

Post by Kansas Ed »

I always resize before Photobucket Using MS Picture Viewer. What program is used on your computer to view the pics?

Ed
Charlie
Levergunner 2.0
Posts: 149
Joined: Thu Nov 19, 2009 11:56 am

Re: 40 Caliber Volcanic Rifle,

Post by Charlie »

Here is a close up of the breech end.

Image
Charlie
Levergunner 2.0
Posts: 149
Joined: Thu Nov 19, 2009 11:56 am

Re: 40 Caliber Volcanic Rifle,

Post by Charlie »

Here is the Magazine Block removed from the Barrel Extension.

Image
Charlie
Levergunner 2.0
Posts: 149
Joined: Thu Nov 19, 2009 11:56 am

Re: 40 Caliber Volcanic Rifle,

Post by Charlie »

The next thing we need to do is solder the Magazine Tubes underneath the Barrel. I will get pictures and explain how I did it , soon to come.

Later,

Charlie
Ben_Rumson
Advanced Levergunner
Posts: 2569
Joined: Sat Sep 15, 2007 12:51 pm

Re: 40 Caliber Volcanic Rifle,

Post by Ben_Rumson »

Sweet... Really kook forward to THIS 8) post!
"IT IS MY OPINION, AND I AM CORRECT SO DON'T ARGUE, THE 99 SAVAGE IS THE FINEST RIFLE EVER MADE IN AMERICA."
WIL TERRY
Charlie
Levergunner 2.0
Posts: 149
Joined: Thu Nov 19, 2009 11:56 am

Re: 40 Caliber Volcanic Rifle,

Post by Charlie »

Those Magazine tubes were made from 5/8 OD, X 7/16 ID, AISI ~ 1018 Mechanical tubing.
I cut them to length, 5.030 for the Magazine Block, 19.281 for the Barrel. Turned the OD to Ø.562, and we are ready to solder.
With some good clamps and holding your mouth just right, you can get a good soldering job.
I made the clamps shown here from 1/4 X 1 Flat Bar
I prepared the parts,
fluxed them,
heated them and applied solder,
spread the solder with steel wool over the area that wants to be mated with the other part,
(both parts)
clamped them together with the clamps,
layed short lengths of solder (.38 Lg.) every 2" or so on the joint.
heated the entire Assembly from underneath until the solder melted and ran down into the joint.
Added a little more solder to the joint.
Let them cool, removed the clamps, and spent the rest of the afternoon cleaning them up.

I will take some pictures of the Soldering Job next and show you what we got.


Image

Later,

Charlie
Charlie
Levergunner 2.0
Posts: 149
Joined: Thu Nov 19, 2009 11:56 am

Re: 40 Caliber Volcanic Rifle,

Post by Charlie »

Here she is, all soldered together, close-ups to follow.



Image
Chuck 100 yd
Advanced Levergunner
Posts: 6972
Joined: Tue Apr 03, 2007 8:52 pm
Location: Ridgefield WA. USA

Re: 40 Caliber Volcanic Rifle,

Post by Chuck 100 yd »

WOW ! That is so cool ! Cant wait for more. :D
Charlie
Levergunner 2.0
Posts: 149
Joined: Thu Nov 19, 2009 11:56 am

Re: 40 Caliber Volcanic Rifle,

Post by Charlie »

Muzzle.

Image

Here is a picture of the original Volcanic muzzle, showing the Locking Key and rotation limiter.
You do not have the required permissions to view the files attached to this post.
Last edited by Charlie on Wed Nov 25, 2009 10:14 am, edited 2 times in total.
Charlie
Levergunner 2.0
Posts: 149
Joined: Thu Nov 19, 2009 11:56 am

Re: 40 Caliber Volcanic Rifle,

Post by Charlie »

Breech.

Image
Charlie
Levergunner 2.0
Posts: 149
Joined: Thu Nov 19, 2009 11:56 am

Re: 40 Caliber Volcanic Rifle,

Post by Charlie »

Here is the Magazine Block removed from the Barrel.

I got some stuff to talk about here concerning that Left Hand Thread, I will go in to it tomorrow.

There is a protruding tab under the Barrel that is pushed toward the Action by a long spring. this Spring pushes the Cartridges back into the Action where they are lifted up and shoved into the Chamber by the Bolt. To load this Gun, this Tab is pulled up into the Magazine Block, compressing the Spring in front of it, the Magazine Block is un-locked and rotated Clockwise about 35º exposing the Magazine tube for droping the Cartridges into it. This Rifle with the 25" Barrel will hold 25 shots and one in the Chamber.

On the original "Volcanic", and "Henry", the Magazine Block was held on the Barrel extension by a collar which had the front sight mounted to it. This collar did not rotate but allowed the Magazine block to rotate, it also had a recess milled in the front that served as a stop to limit the rotation of the magazine Block.

In keeping with the method and spirit of the original, my Rifle opperates the same as theirs, however, I have designed a different way to retain the rotating Magazine Block and limit the rotation. My Magazine Block is held on the Barrel extension by this Left Hand thread. The thread is timed so that when it is bottomed out, the tubes line up with each other. The reason for the Left Hand thread is so that as the Magazine Block is rotated Clockwise, it backs away from the Barrel instead of tightening into it.

Notice the tube has had a .25 Lg. plug pressed into it, blocking off the front. It has also been bored out to Ø.500 to accept the Locking Sleave which I have yet to make, or explain how it works.

The next thing I will do is mill that Slot along the underneath of the Barrel, and then make the Lock Sleave, then wind a spring and make the Cartridge Pusher.

Later my Friends,

Charlie

Image
Last edited by Charlie on Wed Nov 25, 2009 8:51 am, edited 4 times in total.
User avatar
kimwcook
Advanced Levergunner
Posts: 7978
Joined: Tue Sep 04, 2007 10:01 pm
Location: Soap Lake, WA., U.S.A.

Re: 40 Caliber Volcanic Rifle,

Post by kimwcook »

This is so cool, Charlie. Very clean looking work. I love watching skilled work. It's inspiring.
Old Law Dawg
User avatar
Ysabel Kid
Moderator
Posts: 27790
Joined: Mon Sep 17, 2007 7:10 pm
Location: South Carolina, USA
Contact:

Re: 40 Caliber Volcanic Rifle,

Post by Ysabel Kid »

kimwcook wrote: It's inspiring.
That sums it up nicely! 8)
Image
User avatar
JReed
Advanced Levergunner
Posts: 5509
Joined: Tue Apr 03, 2007 11:17 am
Location: SoCal

Re: 40 Caliber Volcanic Rifle,

Post by JReed »

Awesome work Charlie you are indeed gifted. :D Can't wait to see the rest of this gun.
Jeremy
GySgt USMC Ret

To err is human, To forgive is devine, Neither of which is Marine Corps policy
Semper Fidelis
Alan Wood
Levergunner 3.0
Posts: 752
Joined: Sun Dec 28, 2008 11:41 pm

Re: 40 Caliber Volcanic Rifle,

Post by Alan Wood »

Thank you for writing this up with Pictures Charlie. Looking good there!
User avatar
Griff
Posting leader...
Posts: 20803
Joined: Sat Mar 31, 2007 4:56 pm
Location: OH MY GAWD they installed a STOP light!!!

Re: 40 Caliber Volcanic Rifle,

Post by Griff »

Excellent. Just what you've done so far is way over my head... But, still neat that an average (yeah right, genius is more like it), can do this stuff!
Griff,
SASS/CMSA #93
NRA Patron
GUSA #93

There is a fine line between hobby & obsession!
AND... I'm over it!!
No I ain't ready, but let's do it anyway!
Charlie
Levergunner 2.0
Posts: 149
Joined: Thu Nov 19, 2009 11:56 am

Re: 40 Caliber Volcanic Rifle,

Post by Charlie »

Hey Guys, thanks for the nice compliments and expressions of appreciation.
This encourages me to continue.
After all, I would not do this if nobody was interested.

Go back and read where I explained how my Magazine Block works, I think you will like it.

Later,

Charlie
Post Reply