ot-What twist for round ball?
Forum rules
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
-
- Senior Levergunner
- Posts: 1504
- Joined: Tue Sep 04, 2007 1:02 pm
- Location: Eastern Ohio, Foothills of Appalachia
- Contact:
ot-What twist for round ball?
I picked up a Connecticut Valley Arms Buckhorn Magnum in-line muzzleloader for 25 bucks a few weeks ago. It was horrible. Someone shot it, pyrodex we believe, then put it away, uncleaned, wrapped up in plastic bags for several years. Interesting technique. But being the kind to take a chance, I bought it. My buddy and I tore it down and the bore was probably down 20% in size with "stuff" and the action area had a lot of visible rust. The screw in chamber plug was rusty too. Or at least everything looked that way. But after some 20 minutes with brushes and swabs the rifling looked good inside a darker bore. Still some pits in the bore but darn it it cleaned up a lot. The breach plug got bead blasted and but for a few pits on the chamber side, all there. Now right off, I didn't know about the need for 209 primers to shoot this thing. Every other black powder gun I own shoots percussion caps and I never looked. So we chucked up the breach plug in the lathe and chopped and channelled and low and behold, now she is tapped for a nipple to screw in. Made a spanner to remove the plug with the nipple installed and now it shoots percussion caps. Sweet. Then I removed the rear sight and with a different screw, relocated it back to the rear scope block hole, thus lengthening the sight radius. So we start shooting and at 25 yards, its OK but at a hundred it's all over the place. Now my question. I only shoot round ball and black powder and this gun has a 1-28 twist. Is this twist too fast or a round ball? My buddy thinks this gun may have been designed for sabots. Any thoughts?
Gobbler
Gobbler
Click Click Boom
Re: ot-What twist for round ball?
I wouldn’t blame the fast rifling just yet. Yes it’s true, round balls do better with a slower twist. Example 1 in 66” My suggestion, and what I would try is a few different patch thickness and ball size variations. What I think you maybe experiencing is stripping. The rifling maybe all but gone, and also the fact it’s a fast twist for round ball. The end result the patched round ball is just tearing through the rifling and not catching and spinning at all.
-
- Senior Levergunner
- Posts: 1194
- Joined: Wed Sep 19, 2007 9:44 am
- Location: southwest Florida
Re: ot-What twist for round ball?
Way too fast. My round ball rifle is something over 1 in 60. If you dont want to do the sabot route you could try some maxi-ball type bullets.
I've also goteen good accuracy from Power Belt bullets.
I've also goteen good accuracy from Power Belt bullets.
Re: ot-What twist for round ball?
When the mfgs went to the sabot and conicals like the power belt (a sort of sabot-less sabot) they found that the 1-48" twist then commonly used as a compromise twist rate for RB and lead conical shooters was just too slow. They switched to faster twist rates. I'd say your gun is intended for sabots. Unfortunately, being pitted/dark it is likely going to accumulate plastic fouling rather quickly. Using the heavier lead conicals might work well for you or the Power-Belts with their abbreviated length of plastic might be a good compromise. The only way to know is to shoot them.
If you do shoot round ball you can load it down so that it doesn't "strip" the rifling and it might do well on small game.
BTW, if you are going to shoot sabots, get the sabots in the big bags and buy Hornday XTPs in the 100 ct. box. MUCH cheaper than buying the containers of 15-20 projectiles commonly sold as in-line fodder.
If you do shoot round ball you can load it down so that it doesn't "strip" the rifling and it might do well on small game.
BTW, if you are going to shoot sabots, get the sabots in the big bags and buy Hornday XTPs in the 100 ct. box. MUCH cheaper than buying the containers of 15-20 projectiles commonly sold as in-line fodder.
Sincerely,
Hobie
"We are all travelers in the wilderness of this world, and the best that we find in our travels is an honest friend." Robert Louis Stevenson
Hobie
"We are all travelers in the wilderness of this world, and the best that we find in our travels is an honest friend." Robert Louis Stevenson
- Old Savage
- Posting leader...
- Posts: 16740
- Joined: Mon Sep 03, 2007 3:43 pm
- Location: Southern California
Re: ot-What twist for round ball?
My 1 in 48 twist will shoot round ball well to about 1750 maybe a bit more. 1 in 28 of course is for the sabots etc.
- AJMD429
- Posting leader...
- Posts: 32245
- Joined: Sun Sep 09, 2007 10:03 am
- Location: Hoosierland
- Contact:
Re: ot-What twist for round ball?
Dumb question, but how about paper-patching if the plastic sabots would foul the old bore too much?
Doctors for Sensible Gun Laws
"first do no harm" - gun control LAWS lead to far more deaths than 'easy access' ever could.
Want REAL change? . . . . . "Boortz/Nugent in 2012 . . . ! "
"first do no harm" - gun control LAWS lead to far more deaths than 'easy access' ever could.
Want REAL change? . . . . . "Boortz/Nugent in 2012 . . . ! "
Re: ot-What twist for round ball?
I've never heard about anyone doing that. Seems like a needlessly complicated process in doing over a redundancy. I can see problems loading the thing in getting paper-patch, sabot and bullet to hang together in the "pouch" and from there to the bore and being seated without tearing up anything. Also, one would have to custom make some sabots to work with the added thickness of the paper-patch.AJMD429 wrote:Dumb question, but how about paper-patching if the plastic sabots would foul the old bore too much?
Seems one should try it with the sabots, heavier bullets seem to tend to being more accurate but..., and then move to Power Belts and then lead conicals.
Sincerely,
Hobie
"We are all travelers in the wilderness of this world, and the best that we find in our travels is an honest friend." Robert Louis Stevenson
Hobie
"We are all travelers in the wilderness of this world, and the best that we find in our travels is an honest friend." Robert Louis Stevenson
Re: ot-What twist for round ball?
FWIW, plastic/sabot shooters may benefit on the fouling side by running a loose patch downbore after loading, wetted with a Teflon spray.
.
.
- Griff
- Posting leader...
- Posts: 20869
- Joined: Sat Mar 31, 2007 4:56 pm
- Location: OH MY GAWD they installed a STOP light!!!
Re: ot-What twist for round ball?
As said WAY to fast for RB... but as Hobie suggests, run some ½ charge loads and see how it'll do. For plinkin' fun, they're fine... plus powder lasts twice as LONG!Hobie wrote:When the mfgs went to the sabot and conicals like the power belt (a sort of sabot-less sabot) they found that the 1-48" twist then commonly used as a compromise twist rate for RB and lead conical shooters was just too slow. They switched to faster twist rates. I'd say your gun is intended for sabots. Unfortunately, being pitted/dark it is likely going to accumulate plastic fouling rather quickly. Using the heavier lead conicals might work well for you or the Power-Belts with their abbreviated length of plastic might be a good compromise. The only way to know is to shoot them.
If you do shoot round ball you can load it down so that it doesn't "strip" the rifling and it might do well on small game.
BTW, if you are going to shoot sabots, get the sabots in the big bags and buy Hornday XTPs in the 100 ct. box. MUCH cheaper than buying the containers of 15-20 projectiles commonly sold as in-line fodder.
Griff,
SASS/CMSA #93
NRA Patron
GUSA #93
There is a fine line between hobby & obsession!
AND... I'm over it!!
No I ain't ready, but let's do it anyway!
SASS/CMSA #93
NRA Patron
GUSA #93
There is a fine line between hobby & obsession!
AND... I'm over it!!
No I ain't ready, but let's do it anyway!
Re: ot-What twist for round ball?
Pete, I hadn't heard that. How does that work?Pete44ru wrote:FWIW, plastic/sabot shooters may benefit on the fouling side by running a loose patch downbore after loading, wetted with a Teflon spray.
.
Sincerely,
Hobie
"We are all travelers in the wilderness of this world, and the best that we find in our travels is an honest friend." Robert Louis Stevenson
Hobie
"We are all travelers in the wilderness of this world, and the best that we find in our travels is an honest friend." Robert Louis Stevenson
Re: ot-What twist for round ball?
My Lyman Great Plains Hunter with a 1in32 barrel for conicals & sabots will shoot RBs very accurately up to a certain power level.....about 65grs by volume with 777, but beyond that it starts tossin em high & right. jd45
Re: ot-What twist for round ball?
There are examples of original Hawken rifles with 28 twists.
You may need to go with a heavy patch for a tight fit, and 1 gr of blackpowder per caliber. (If you're using any of the fake stuff all bets are off)
You can also try the paper patch route, the biggest problem you may have is finding the proper diameter slugs to wrap.Back in the day of the highclass shooting matches patched bullets were favored, and still are by long range muzzleloader shooters. Paper patching is discussed in depth the Ned Roberts book The Muzzleloading Caplock Rifle.
You may need to go with a heavy patch for a tight fit, and 1 gr of blackpowder per caliber. (If you're using any of the fake stuff all bets are off)
You can also try the paper patch route, the biggest problem you may have is finding the proper diameter slugs to wrap.Back in the day of the highclass shooting matches patched bullets were favored, and still are by long range muzzleloader shooters. Paper patching is discussed in depth the Ned Roberts book The Muzzleloading Caplock Rifle.
Re: ot-What twist for round ball?
Before you do anything just JB the bore and try a thicker patch. Even go .005 lower on the ball if you have to. But definitely try a thicker patch.
Did you look for your patches down range?? If so, what did they look like?? Burned out or torn?? This makes a big difference.
1in60 or 1in66 is supposedly optimum for round balls. But I have seen way too many fast twist rifles shoot round balls great. Even down to as fast as 1in18. You just have to play around with the ball and patch. Try that first. It will probably work.
Or maybe the barrel is just shot?? Tom.
Did you look for your patches down range?? If so, what did they look like?? Burned out or torn?? This makes a big difference.
1in60 or 1in66 is supposedly optimum for round balls. But I have seen way too many fast twist rifles shoot round balls great. Even down to as fast as 1in18. You just have to play around with the ball and patch. Try that first. It will probably work.
Or maybe the barrel is just shot?? Tom.
-
- Senior Levergunner
- Posts: 1504
- Joined: Tue Sep 04, 2007 1:02 pm
- Location: Eastern Ohio, Foothills of Appalachia
- Contact:
Re: ot-What twist for round ball?
Thanks for the replies so far folks. The balls are .495 and the greased patches I have are .0125 and it takes as firm a hand at loading as any of the other muzzle loaders I have. What would be the benefit of a smaller ball and thicker patch? I've never heard of that one but it's intriguing. Unfortunately I never did look for the patches. That would have been a good idea. As for what powder, I'm too old school for powder substitutes so I only shoot black. 2f for the .50 cal., same for the Hawken I have, and a 50 grain load is what I used the other day. I would like to keep a watch for a .50 Minnie ball style or something to try.
Gobbler
Gobbler
Click Click Boom