Need a source for 32-40 brass
Forum rules
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
-
- Senior Levergunner
- Posts: 1082
- Joined: Mon Sep 03, 2007 5:36 pm
- Location: Western Australia
Need a source for 32-40 brass
Does anyone know of one with stock on hand?
-
- Levergunner 2.0
- Posts: 107
- Joined: Tue Oct 02, 2007 12:31 am
- Location: California
Re: Need a source for 32-40 brass
Try http://www.huntingtons.com call their toll free number 1-866-735-6237 for stock.
http://www.midwayusa.com is accepting back orders with a due date 0f 8/29/2009
http://www.impactguns.com/store/winchester_brass.html is accepting orders.
Buffalo Arms has them formed from .38-55 until they are available again. http://www.buffaloarms.com/browse.cfm/4,139.html
.32-40 is probably like .348 Winchester, a seasonal item produced when they have enough demand.
Otherwise it can be formed from .30-30, .32 Special or .38-55, or even .375 Winchester brass although the cases come out slightly shorter. Good luck.
http://www.midwayusa.com is accepting back orders with a due date 0f 8/29/2009
http://www.impactguns.com/store/winchester_brass.html is accepting orders.
Buffalo Arms has them formed from .38-55 until they are available again. http://www.buffaloarms.com/browse.cfm/4,139.html
.32-40 is probably like .348 Winchester, a seasonal item produced when they have enough demand.
Otherwise it can be formed from .30-30, .32 Special or .38-55, or even .375 Winchester brass although the cases come out slightly shorter. Good luck.
-
- Senior Levergunner
- Posts: 1082
- Joined: Mon Sep 03, 2007 5:36 pm
- Location: Western Australia
Re: Need a source for 32-40 brass
Thanks, John
- Shasta
- Senior Levergunner
- Posts: 1558
- Joined: Thu Sep 06, 2007 10:50 pm
- Location: Shasta County, the far right stronghold in California
Re: Need a source for 32-40 brass
California Rifle & Pistol Association LIFE Member
National Rifle Association BENEFACTOR LIFE Member
http://www.hcrpclub.org/schedule.html
avatar pic is Shasta Dam, Shasta Lake, & Mt. Shasta
National Rifle Association BENEFACTOR LIFE Member
http://www.hcrpclub.org/schedule.html
avatar pic is Shasta Dam, Shasta Lake, & Mt. Shasta
- Sixgun
- Posting leader...
- Posts: 18713
- Joined: Sun Sep 16, 2007 7:17 pm
- Location: S.E. Pa. Where The Finest Winchesters & Colts Reside
Re: Need a source for 32-40 brass
Just run a 30-30 case through a 32-40 fls. It comes up a bit short but seat the bullet to the proper oal. I've been doing that for 30+ years with many old 32-40's.---------------Sixgun
Re: Need a source for 32-40 brass
Hi Bruce,
Did you find any 32-40 brass? I am after some as well.
I have run 38-55 cases through 32-40 dies with good results but would like some 32-40 head stamped brass as well.
Tried 30-30 but they end up about 2mm too short.
Please let me know if you found some.
Regards, Pop.
Did you find any 32-40 brass? I am after some as well.
I have run 38-55 cases through 32-40 dies with good results but would like some 32-40 head stamped brass as well.
Tried 30-30 but they end up about 2mm too short.
Please let me know if you found some.
Regards, Pop.
-
- Senior Levergunner
- Posts: 1082
- Joined: Mon Sep 03, 2007 5:36 pm
- Location: Western Australia
Re: Need a source for 32-40 brass
Pop,
No luck so far.
I am using .30-30 cases, which as you and Sixgun have mentioned come up a bit short.
No luck so far.
I am using .30-30 cases, which as you and Sixgun have mentioned come up a bit short.
Re: Need a source for 32-40 brass
Bruce there is a little hole in the wall place in town here that had 32 brass just cann't remember if it was 32-40 or 32 winchester special but I'll check and let you know what I find one way or the other, may take sometime as he sets his time in the shop on his mood for the day.
Re: Need a source for 32-40 brass
Bombed out on this.Did run acrossed 38-55 but that was about it.
-
- Levergunner 2.0
- Posts: 235
- Joined: Fri Jan 16, 2009 12:46 pm
- Location: Ft Hood , Tx area
Re: Need a source for 32-40 brass
Every 10 yrs Winc makes a run of 32-40 brass and it is near it due date or look for JW loaded .
..
......
......
Re: Need a source for 32-40 brass
I run into .32-40 brass occasionally. I will keep you in mind. Regards, 1886.
Re: Need a source for 32-40 brass
I picked up 20 new w/W cases for you today. Let me know if you want them. I know where you can get more. Take Care, 1886.
-
- Senior Levergunner
- Posts: 1082
- Joined: Mon Sep 03, 2007 5:36 pm
- Location: Western Australia
Re: Need a source for 32-40 brass
Many thanks for all replies and your offer, 1886.
I will PM you separately.
Sincerely,
Bruce
I will PM you separately.
Sincerely,
Bruce