Headspace in a Lever Action with a Straight-wall Case
Forum rules
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
Headspace in a Lever Action with a Straight-wall Case
Yes, I could have a qualified gunsmith check it over but...
But... The 1892 Winchester (made in 1910) that I picked up recently is just begging to be shot!
It was rebarreled to .357 Mag and still has the original "blackpowder" firing pin, but I've been advised by the best (a forum member here) that it should be OK with lead loads, as long as I see no primer leakage.
The headspace though, as measured by seating a once-fired primer very shallow, and then letting the closing of the action seat it (with extractor and ejector still on the bolt) -- comes out at 0.018"...
Now I understand that with a bottleneck round, I'd risk stretching the brass and having a casehead separation -- which would not be fun...
But in a straight-walled case like 357 brass, using 4.5 gr of Universal reloads with lead bullets... Is that headspace OK?
And if it's not... What's the fix?
Thanks all!
Old No7
But... The 1892 Winchester (made in 1910) that I picked up recently is just begging to be shot!
It was rebarreled to .357 Mag and still has the original "blackpowder" firing pin, but I've been advised by the best (a forum member here) that it should be OK with lead loads, as long as I see no primer leakage.
The headspace though, as measured by seating a once-fired primer very shallow, and then letting the closing of the action seat it (with extractor and ejector still on the bolt) -- comes out at 0.018"...
Now I understand that with a bottleneck round, I'd risk stretching the brass and having a casehead separation -- which would not be fun...
But in a straight-walled case like 357 brass, using 4.5 gr of Universal reloads with lead bullets... Is that headspace OK?
And if it's not... What's the fix?
Thanks all!
Old No7
"Freedom and the Second Amendment... One cannot exist without the other." © 2000 DTH
-
- Senior Levergunner
- Posts: 1232
- Joined: Thu Sep 17, 2009 3:45 pm
- Location: Dartmouth, MA
- Contact:
Re: Headspace in a Lever Action with a Straight-wall Case
I'm not going to say it's "OK".........................
But I'd shoot it all day long with light Cowboy Loads.................Just my opinion.
But I'd shoot it all day long with light Cowboy Loads.................Just my opinion.
- earlmck
- Advanced Levergunner
- Posts: 3446
- Joined: Tue Nov 30, 2010 12:10 am
- Location: pert-neer middle of Oregon
Re: Headspace in a Lever Action with a Straight-wall Case
Yeah, that seems like quite a bit of excess headspace, No7. But I'm with Roy B -- go ahead and shoot it and I'd bet you don't have any trouble with it. Just saying that 'cause I've never seen a head separation with a straight-wall pistol case. And also I've experienced varying degrees of "badness" with the old blackpowder firing pin. That also may not be a problem with any normal load. And if you get some primer piercing (that's what you'll see -- a hole in your primer that makes you think the firing pin was too long and sharp) you can try switching to Remington primers. I've never gotten a hole in a Remington 7 1/2 primer and I have a couple rifles that have those big sloppy firing pin holes and won't let me use a CCI or Winchester small pistol primer...
So now you've got a couple votes from the "try it and see how it goes" crowd.
So now you've got a couple votes from the "try it and see how it goes" crowd.
The greatest patriot...
is he who heals the most gullies. Patrick Henry
is he who heals the most gullies. Patrick Henry
- Old Time Hunter
- Advanced Levergunner
- Posts: 2388
- Joined: Sun Apr 01, 2007 11:18 am
- Location: Wisconsin
Re: Headspace in a Lever Action with a Straight-wall Case
Before you shoot it, build up .007 to 010" of masking tape on the back of a spent shell and see how easy it cycles. Have seen quite a few bolts with the center concave.
-
- Site Sponsor
- Posts: 2507
- Joined: Fri Sep 07, 2007 12:05 pm
- Location: Lampasas, Texas
- Contact:
Re: Headspace in a Lever Action with a Straight-wall Case
I do feel you will be ok with the BP firing pin and any load that doesn't flow the primer back into the hole. But, at .018 headspace if you shoot it much it's only going to get worse. in the black powder era .010 was considered acceptable. Now days .005 or less is the norm for smokeless. What you need to do is find where the slack is.Old No7 wrote:Yes, I could have a qualified gunsmith check it over but...
But... The 1892 Winchester (made in 1910) that I picked up recently is just begging to be shot!
It was rebarreled to .357 Mag and still has the original "blackpowder" firing pin, but I've been advised by the best (a forum member here) that it should be OK with lead loads, as long as I see no primer leakage.
The headspace though, as measured by seating a once-fired primer very shallow, and then letting the closing of the action seat it (with extractor and ejector still on the bolt) -- comes out at 0.018"...
Now I understand that with a bottleneck round, I'd risk stretching the brass and having a casehead separation -- which would not be fun...
But in a straight-walled case like 357 brass, using 4.5 gr of Universal reloads with lead bullets... Is that headspace OK?
And if it's not... What's the fix?
Thanks all!
Old No7
What you might try is take it apart and then use feeler gages to measure the gap between the locking bolts in their frame cuts.If there is excess front to back play you can tighten them some by forging the locking bolts wider where they engage the breech bolt. If you can't get it close to .010 you may have to set the barrel back.
The problem with excessive headspace isn't just case damage. Think of it as if it's a bowlong ball in the back of your pickup. as long as it's contained in a ball bag or box it can't do much damage but if it loose back there it's gonna leave some marks.
Steve Young aka Nate Kiowa Jones Sass# 6765
Steve's Guns aka "Rossi 92 Specialists"
205 Antler lane
Lampasas, Texas 76550
http://www.stevesgunz.com
Email; steve@stevesgunz.com
Tel: 512-564-1015
Steve's Guns aka "Rossi 92 Specialists"
205 Antler lane
Lampasas, Texas 76550
http://www.stevesgunz.com
Email; steve@stevesgunz.com
Tel: 512-564-1015
- Buck Elliott
- Member Emeritus
- Posts: 2830
- Joined: Mon Sep 10, 2007 12:15 pm
- Location: Halfway up Sheep Mountain -- Cody, Wyoming
Re: Headspace in a Lever Action with a Straight-wall Case
Case stretching, and eventual head seperation is almost guaranteed, with that much headspace, firing loads at "normal" .357 pressures...
It's going to happen somewhere down the line, even if everything locks up tight, and headspace is at a minimum, but with that much "running room," it's going to occur much sooner, rather than later, and will continue to batter the old action, increasing the wear and tear...
It's going to happen somewhere down the line, even if everything locks up tight, and headspace is at a minimum, but with that much "running room," it's going to occur much sooner, rather than later, and will continue to batter the old action, increasing the wear and tear...
Regards
Buck
Life has a way of making the foreseeable that which never happens, and the unforeseeable, that which your life becomes...
Buck
Life has a way of making the foreseeable that which never happens, and the unforeseeable, that which your life becomes...
- gundownunder
- Senior Levergunner
- Posts: 1449
- Joined: Fri Sep 07, 2007 12:02 pm
- Location: Perth. Western Australia
Re: Headspace in a Lever Action with a Straight-wall Case
Just in case it's an important question,
Is anything nasty likely to happen if a seriously heavy 357 magnum load gets put in that old gun by mistake?
Is anything nasty likely to happen if a seriously heavy 357 magnum load gets put in that old gun by mistake?
Bob
***********************************
You have got to love democracy-
It lets you choose who your dictator is going to be.
***********************************
***********************************
You have got to love democracy-
It lets you choose who your dictator is going to be.
***********************************
-
- Site Sponsor
- Posts: 2507
- Joined: Fri Sep 07, 2007 12:05 pm
- Location: Lampasas, Texas
- Contact:
Re: Headspace in a Lever Action with a Straight-wall Case
Because the 92 action is a strong design anything short of an overload will probably not cause a catastrophic failure. The gun is going to just get looser and looser. Particularly with the pre-WWI metal being suspect, too. It has been my experience that the post WWI guns converted to 357mag tend to hold up better if set up with correct headspace. However, the ones converted to 44mag tend to shoot loose regardless. Of the ones I’ve seen I don’t have any way to know how well they were set up initially so it’s possible they too started with excessive headspace.gundownunder wrote:Just in case it's an important question,
Is anything nasty likely to happen if a seriously heavy 357 magnum load gets put in that old gun by mistake?
Steve Young aka Nate Kiowa Jones Sass# 6765
Steve's Guns aka "Rossi 92 Specialists"
205 Antler lane
Lampasas, Texas 76550
http://www.stevesgunz.com
Email; steve@stevesgunz.com
Tel: 512-564-1015
Steve's Guns aka "Rossi 92 Specialists"
205 Antler lane
Lampasas, Texas 76550
http://www.stevesgunz.com
Email; steve@stevesgunz.com
Tel: 512-564-1015
-
- Levergunner 1.0
- Posts: 92
- Joined: Fri Sep 28, 2007 1:14 pm
Re: Headspace in a Lever Action with a Straight-wall Case
Years ago I bought a cheap automotive feeler gauge . I cut shims from it and use them between the bolt face and a no-go head space gauge .
If you try to determine the space between the front of the bolt & the back of the case , I suggest you use something like that , instead of tape .
If you determine the rifle needs major work , consider the cost vs the cost of a Rossi M92 clone . And make the old gun a wall hanger .
God bless
Wyr
If you try to determine the space between the front of the bolt & the back of the case , I suggest you use something like that , instead of tape .
If you determine the rifle needs major work , consider the cost vs the cost of a Rossi M92 clone . And make the old gun a wall hanger .
God bless
Wyr
Re: Headspace in a Lever Action with a Straight-wall Case
Try some small rifle primers in those cases. Those big ol rifle firing pins sometimes mash the stuff out of pistol primers and it looks like either headspace or pressure issues , when it really isn't.
Also try a real headspace guage. Using fired primers , you might as well be using the rule on your leatherman as far as accurate measures are concerned.
Also try a real headspace guage. Using fired primers , you might as well be using the rule on your leatherman as far as accurate measures are concerned.