Drilling knife blades
Forum rules
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
-
- Advanced Levergunner
- Posts: 4145
- Joined: Fri Dec 21, 2007 11:34 am
- Location: north of Palacios about 1400 miles
Drilling knife blades
I've been making knives with deer antlers for handles, how do you drill holes thru them, have a cobalt drill bit and had a really tough time a Winchester knife. The Solingen is just a hard. Any hints tips or info. Thanks Todd/3leg
30/30 Winchester: Not accurate enough fer varmints, barely adequate for small deer; BUT In a 10" to 14" barrelled pistol; is good for moose/elk to 200 yards; ground squirrels to 300 metres
250 Savage... its what the 223 wishes it could be...!
250 Savage... its what the 223 wishes it could be...!
- AJMD429
- Posting leader...
- Posts: 32215
- Joined: Sun Sep 09, 2007 10:03 am
- Location: Hoosierland
- Contact:
Re: Drilling knife blades
A straight flute carbide bit I got from MidwayUSA will go through the hardest gun parts I've seen, so maybe try one of those. Use cutting oil.
Doctors for Sensible Gun Laws
"first do no harm" - gun control LAWS lead to far more deaths than 'easy access' ever could.
Want REAL change? . . . . . "Boortz/Nugent in 2012 . . . ! "
"first do no harm" - gun control LAWS lead to far more deaths than 'easy access' ever could.
Want REAL change? . . . . . "Boortz/Nugent in 2012 . . . ! "
-
- Advanced Levergunner
- Posts: 4145
- Joined: Fri Dec 21, 2007 11:34 am
- Location: north of Palacios about 1400 miles
Re: Drilling knife blades
Never thought about carbide! Duh These blades make bed frames seem like aluminum.. thanks Doc
30/30 Winchester: Not accurate enough fer varmints, barely adequate for small deer; BUT In a 10" to 14" barrelled pistol; is good for moose/elk to 200 yards; ground squirrels to 300 metres
250 Savage... its what the 223 wishes it could be...!
250 Savage... its what the 223 wishes it could be...!
- Buck Elliott
- Member Emeritus
- Posts: 2830
- Joined: Mon Sep 10, 2007 12:15 pm
- Location: Halfway up Sheep Mountain -- Cody, Wyoming
Re: Drilling knife blades
For fast holes, drill slow..
And use good cutting oil..
High drill speeds can work-harden some steels..
And use good cutting oil..
High drill speeds can work-harden some steels..
Regards
Buck
Life has a way of making the foreseeable that which never happens, and the unforeseeable, that which your life becomes...
Buck
Life has a way of making the foreseeable that which never happens, and the unforeseeable, that which your life becomes...
- GunnyMack
- Advanced Levergunner
- Posts: 10198
- Joined: Mon Sep 19, 2016 7:57 am
- Location: Not where I want to be!
Re: Drilling knife blades
Smaller diameter drill = high RPM, lots of lube!
Yes carbide drill, most any machine tool supply house has them.
You could also spot anneal by heating a steel rod to red heat and hold it to the spot you want to drill. You have to hold it in place until the rod cools. Make sure the knife handle is the heat sink, not your vise!
It may take a few times which is a PITA!
Yes carbide drill, most any machine tool supply house has them.
You could also spot anneal by heating a steel rod to red heat and hold it to the spot you want to drill. You have to hold it in place until the rod cools. Make sure the knife handle is the heat sink, not your vise!
It may take a few times which is a PITA!
BROWN LABS MATTER !!
-
- Site Sponsor
- Posts: 2507
- Joined: Fri Sep 07, 2007 12:05 pm
- Location: Lampasas, Texas
- Contact:
Re: Drilling knife blades
Steve Young aka Nate Kiowa Jones Sass# 6765
Steve's Guns aka "Rossi 92 Specialists"
205 Antler lane
Lampasas, Texas 76550
http://www.stevesgunz.com
Email; steve@stevesgunz.com
Tel: 512-564-1015
Steve's Guns aka "Rossi 92 Specialists"
205 Antler lane
Lampasas, Texas 76550
http://www.stevesgunz.com
Email; steve@stevesgunz.com
Tel: 512-564-1015
Re: Drilling knife blades
You can get carbide drill bits at Harbor Freight. Use a drill press and a vise. The tungsten bits snap if they are put in a bind. I like the ones for rotary tools.
D. Brian Casady
Quid Llatine Dictum Sit, Altum Viditur.
Advanced is being able to do the basics while your leg is on fire---Bill Jeans
Don't ever take a fence down until you know why it was put up---Robert Frost
Quid Llatine Dictum Sit, Altum Viditur.
Advanced is being able to do the basics while your leg is on fire---Bill Jeans
Don't ever take a fence down until you know why it was put up---Robert Frost
-
- Advanced Levergunner
- Posts: 6972
- Joined: Tue Apr 03, 2007 8:52 pm
- Location: Ridgefield WA. USA
Re: Drilling knife blades
Inexpensive masonry drill bits have carbide tips and can be used to drill hardened steel. Be careful not to overheat them and lighten up the pressure when breaking through the far side as that is when most drill bits catch and are broken.