Need a source for 32-40 brass

Bruce Scott · Post by **Bruce Scott** » Sun Aug 16, 2009 7:02 pm

Does anyone know of one with stock on hand?

Wrangler John · Post by **Wrangler John** » Mon Aug 17, 2009 6:56 am

Try http://www.huntingtons.com call their toll free number 1-866-735-6237 for stock.

http://www.midwayusa.com is accepting back orders with a due date 0f 8/29/2009

http://www.impactguns.com/store/winchester_brass.html is accepting orders.

Buffalo Arms has them formed from .38-55 until they are available again. http://www.buffaloarms.com/browse.cfm/4,139.html

.32-40 is probably like .348 Winchester, a seasonal item produced when they have enough demand.

Otherwise it can be formed from .30-30, .32 Special or .38-55, or even .375 Winchester brass although the cases come out slightly shorter. Good luck.

Bruce Scott · Post by **Bruce Scott** » Mon Aug 17, 2009 6:03 pm

Thanks, John

Shasta · Post by **Shasta** » Tue Aug 18, 2009 7:58 pm

Saw this over on the single shot forum:

http://www.assra.com/cgi-bin/yabb/YaBB. ... 1250208734

Sixgun · Post by **Sixgun** » Sat Aug 22, 2009 3:13 pm

Just run a 30-30 case through a 32-40 fls. It comes up a bit short but seat the bullet to the proper oal. I've been doing that for 30+ years with many old 32-40's.---------------Sixgun

Pop Watts · Post by **Pop Watts** » Fri Aug 28, 2009 7:18 am

Hi Bruce,

Did you find any 32-40 brass? I am after some as well.
I have run 38-55 cases through 32-40 dies with good results but would like some 32-40 head stamped brass as well.
Tried 30-30 but they end up about 2mm too short.

Please let me know if you found some.

Regards, Pop.

Bruce Scott · Post by **Bruce Scott** » Sat Aug 29, 2009 9:46 am

Pop,

No luck so far.

I am using .30-30 cases, which as you and Sixgun have mentioned come up a bit short.

model55 · Post by **model55** » Mon Aug 31, 2009 8:18 pm

Bruce there is a little hole in the wall place in town here that had 32 brass just cann't remember if it was 32-40 or 32 winchester special but I'll check and let you know what I find one way or the other, may take sometime as he sets his time in the shop on his mood for the day.

model55 · Post by **model55** » Sat Sep 05, 2009 11:49 pm

Bombed out on this.Did run acrossed 38-55 but that was about it.

TX Gun Runner · Post by **TX Gun Runner** » Sun Sep 06, 2009 4:02 am

Every 10 yrs Winc makes a run of 32-40 brass and it is near it due date or look for JW loaded .

1886 · Post by **1886** » Sun Sep 06, 2009 5:25 am

I run into .32-40 brass occasionally. I will keep you in mind. Regards, 1886.

1886 · Post by **1886** » Sun Sep 06, 2009 2:41 pm

I picked up 20 new w/W cases for you today. Let me know if you want them. I know where you can get more. Take Care, 1886.

Bruce Scott · Post by **Bruce Scott** » Sun Sep 06, 2009 5:58 pm

Many thanks for all replies and your offer, 1886.

I will PM you separately.

Sincerely,
Bruce

Need a source for 32-40 brass

Need a source for 32-40 brass

Re: Need a source for 32-40 brass

Re: Need a source for 32-40 brass

Re: Need a source for 32-40 brass

Re: Need a source for 32-40 brass

Re: Need a source for 32-40 brass

Re: Need a source for 32-40 brass

Re: Need a source for 32-40 brass

Re: Need a source for 32-40 brass

Re: Need a source for 32-40 brass

Re: Need a source for 32-40 brass

Re: Need a source for 32-40 brass

Re: Need a source for 32-40 brass