Is there one for the ejector plunger/stop pin?
I tried straight reverse order, and found it to be difficult with the plunger in place, so I left it out. Have the gun back together with the exception of the plunger and it's pin. I'm trying to get it aligned with a small pick, no joy. What's the trick?
yes, I have the instructions. I need secret tricks.
Rossi 92 reassembly secret?
Forum rules
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
- jamesgpobog
- Levergunner
- Posts: 49
- Joined: Tue Oct 01, 2013 2:49 pm
Rossi 92 reassembly secret?
Si vis pacem para bellum
Re: Rossi 92 reassembly secret?
If I understand your dilemma, a case held in place with a finger and the extractor should do it.
Kind regards,
Tycer
----------------------------------------------------------------
http://www.saf.org - https://peakprosperity.com/ - http://www.guntalk.com
Tycer
----------------------------------------------------------------
http://www.saf.org - https://peakprosperity.com/ - http://www.guntalk.com
- jamesgpobog
- Levergunner
- Posts: 49
- Joined: Tue Oct 01, 2013 2:49 pm
Re: Rossi 92 reassembly secret?
I can't get the plunger lined up so it will depress. It wants to rotate out of alignment, also it needs a little wiggle to get the plunger lower rails to line up. and the bolt needs to be forward.Tycer wrote:If I understand your dilemma, a case held in place with a finger and the extractor should do it.
Si vis pacem para bellum
-
- Senior Levergunner
- Posts: 1521
- Joined: Sun Apr 15, 2007 12:52 am
- Location: Leverland, U.S.A.
- Contact:
Re: Rossi 92 reassembly secret?
jamesgpobog,
Put the empty case in the chamber, assemble the breechbolt & put it into the receiver, then push the breechbolt forward, until the extractor snaps over the rim of the empty case. You should have no trouble closing, or keeping closed, the breechbolt, since the ejector is now compressed.
Shawn
Put the empty case in the chamber, assemble the breechbolt & put it into the receiver, then push the breechbolt forward, until the extractor snaps over the rim of the empty case. You should have no trouble closing, or keeping closed, the breechbolt, since the ejector is now compressed.
Shawn
"That's right, Billy, I'm good with it. I hit what I shoot at, and I'm fast!"-Lucas McCain, c1882.
- jamesgpobog
- Levergunner
- Posts: 49
- Joined: Tue Oct 01, 2013 2:49 pm
Re: Rossi 92 reassembly secret?
OK, obviously, I have to take it back apart, no problem, but using your method, do I insert the pin at that point, then assemble the hammer and rear tang?Hagler wrote:jamesgpobog,
Put the empty case in the chamber, assemble the breechbolt & put it into the receiver, then push the breechbolt forward, until the extractor snaps over the rim of the empty case. You should have no trouble closing, or keeping closed, the breechbolt, since the ejector is now compressed.
Shawn
Si vis pacem para bellum
-
- Senior Levergunner
- Posts: 1521
- Joined: Sun Apr 15, 2007 12:52 am
- Location: Leverland, U.S.A.
- Contact:
Re: Rossi 92 reassembly secret?
jamesgpobog,
Yes, that is correct. You'll get it.
Shawn
P.S.
Because it is very similar to your Rossi, this Browning B-92 Field Service Manual will help you:
http://stevespages.com/pdf/browning_b92.pdf
You may ahve to go to the "MANUALS" page, first, though, because hotlinking is not always allowed:
http://stevespages.com/page7b.htm
...then select "Browning B-92 Field Service" to open the manual.
Yes, that is correct. You'll get it.
Shawn
P.S.
Because it is very similar to your Rossi, this Browning B-92 Field Service Manual will help you:
http://stevespages.com/pdf/browning_b92.pdf
You may ahve to go to the "MANUALS" page, first, though, because hotlinking is not always allowed:
http://stevespages.com/page7b.htm
...then select "Browning B-92 Field Service" to open the manual.
"That's right, Billy, I'm good with it. I hit what I shoot at, and I'm fast!"-Lucas McCain, c1882.
-
- Advanced Levergunner
- Posts: 4426
- Joined: Wed Sep 12, 2007 12:33 pm
- Location: Wyoming and Arizona
Re: Rossi 92 reassembly secret?
You will profit greatly from the purchase and study of this DVD:http://stevesgunz.com/dvd.htm